Hoek & Bray¶
For rock slopes, different from those in soil, the Mohr-Coulomb failure criterion can not be used to define the resistance of the material; however with this method is described a procedure that allows the application of the classical methods of Limit Equilibrium even in rocky slopes.
In this purpose are defined the angle of shearing and the cohesion along the sliding surface according to the following expressions:
where:
sc is the uniaxial compressive strength of the rock;
A, B, T constants function of the lithotype and the quality of the rock (table below);
N normal stress at the base of the slice.
The constants A, B and T are determined as a function of the classification of the rocks according to Bieniawski (RMR index) or according to Barton (Q index).
Between the two classifications, on the base of 111 examples analyzed, was found the following correlation:
| RMR =100
Q = 500 | A = 0.816
B = 0.658
T = -0.140 | A = 0.918
B = 0.677
T = -0.099 | A = 1.044
B = 0.692
T = -0.067 | A = 1.086
B = 0.696
T = -0.059 | A = 1.220
B = 0.705
T = -0.040 |
| RMR = 85
Q = 100 | A = 0.651
B = 0.679
T = -0.028 | A = 0.739
B = 0.692
T = -0.020 | A = 0.848
B = 0.702
T = -0.013 | A = 0.883
B = 0.705
T = -0.012 | A = 0.998
B = 0.712
T = -0.008 |
| RMR = 65
Q = 10 | A = 0.369
B = 0.669
T = -0.006 | A = 0.427
B = 0.683
T = -0.004 | A = 0.501
B = 0.695
T = -0.003 | A = 0.525
B = 0.698
T = -0.002 | A = 0.603
B = 0.707
T = -0.002 |
| RMR = 44
Q = 1 | A = 0.198
B = 0.662
T = -0.0007 | A = 0.234
B = 0.675
T = -0.0005 | A = 0.280
B = 0.688
T = -0.0003 | A = 0.295
B = 0.691
T = -0.003 | A = 0.346
B = 0.700
T = -0.0002 |
| RMR = 3
Q = 0.1 | A = 0.115
B = 0.646
T = -0.0002 | A = 0.129
B = 0.655
T = -0.0002 | A = 0.162
B = 0.672
T = -0.0001 | A = 0.172
B = 0.676
T = -0.0001 | A = 0.203
B = 0.686
T = -0.0001 |
| RMR = 3
Q = 0.01 | A = 0.042
B = 0.534
T = 0 | A = 0.050
B = 0.539
T = 0 | A = 0.061
B = 0.546
T = 0 | A = 0.065
B = 0.548
T = 0 | A = 0.078
B = 0.556
T = 0 |
Relation between the classification of the rocks and the parameters A, B and T
Debris over rock in the same slope¶
The Soil slopes / Rock slopes choice in the Main parameters applies to the whole slope. With Rock slopes the program recalculates the shear strength angle and the cohesion on every slice with the Hoek & Bray expressions above, starting from σc, A, B and T of the material; materials without these parameters get default rock values. In the same analysis you therefore cannot have layers described by c′ and φ′ (for example a debris cover) and layers described as a rock mass.
For a stratigraphy with loose debris at the surface and rock at depth:
- in the Main parameters choose Soil slopes;
- give the debris its own φ′ and c′;
- give the rock an equivalent cohesion and friction angle, derived from the rock mass classification. For example, from the Bieniawski (1989) RMR classes:
| Class | RMR | c (kPa) | φ (°) |
|---|---|---|---|
| I | 81–100 | > 400 | > 45 |
| II | 61–80 | 300–400 | 35–45 |
| III | 41–60 | 200–300 | 25–35 |
| IV | 21–40 | 100–200 | 15–25 |
| V | < 20 | < 100 | < 15 |
Alternatively, if σci and mi are known, equivalent c′ and φ′ can be derived from the generalised Hoek-Brown criterion (GSI ≈ RMR89 − 5), linearised over the effective stress range of the slope.
The critical surface often runs in the debris or along the contact with the rock: repeat the analysis with the minimum and maximum values of the class to check that the safety factor does not depend too much on the parameters chosen for the rock.