Slope¶
The full manual of Slope is here: https://help.geostru.io/slope/en/
While performing the global stability analysis, Slope is asking me to activate the program¶
When performing a global stability analysis with GeoStru software (MDC, SPW, GDW, etc...), by setting the directory where Slope's executable file (Slope.exe) is located, the Slope module named GSA for global stability analysis will start.
Slope should be installed as a standalone program. If it's not installed, it will be automatically downloaded by the requesting software. If this does not happen, please contact GeoStru. Slope should be executed at least once as Slope, and subsequent executions should be carried out by the software that requires global stability analysis. During this process, the program creates a data file that is transmitted to Slope/GSA.
The Slope/GSA module allows for global stability analysis but has limitations compared to Slope. You can save the Slope file in Slope/GSA to continue working on more complex stability analyses.
The global stability module must be installed on the same drive as the software that uses it. Additionally, Slope must be of the same version as the software that requires global stability analysis (e.g., 2022, 2023, etc.)
In conclusion, Slope should not be activated unless you have a license, and it should be executed by software such as MDC, SPW ,GDW, etc.
How can I change the units of measurement in Slope?¶
To change the units of measurement in Slope Stability - Slope, go to Preferences and then International Setup:

The window for setting the units will open:

Once the desired units have been selected, press OK. Please note that the software must be restarted for changes to take effect!
N.B.: the units of measurement must be set as soon as the project is created, in fact once the project is saved, it is no longer possible to change them.
When starting the software, the message ‘Unable to start the application. Contact supplier’.¶
To start the software you need to go to the directory where it is installed and start it from there. Directory C:\Users\Nome utente\AppData\Local\Apps\2.0\J5KQQ6Q5.5XM\HAJ7Q5CG.O6V\slop..tion_8dede8a7fd655370_0001.0000_d228a103d6044420
Where in User name is the name of the user connected to his PC and all alphanumeric codes change according to the PC (so they vary according to the example above). Inside the folder starting with ‘slop..tion’ (in the case of Slope, it will be load..tion in the case of Loadcap, mp..tion in the case of MP etc.) there are the software files, inside there is the file ‘Slope.exe’ (Loadcap.exe, MP.exe, SPW.exe, etc.) from which to start the software. Make a shortcut on the desktop. If there are several folders starting with ‘slop..tion’ the most recent one is that of the latest installed version, it means that there are several versions of the software even older. In order to get to this folder, you must activate the Windows hidden files and folders view
I get the error COMDLG32.OCX missing when starting the software file converter¶
The error is due to a missing or unregistered COMDLG32.OCX component in the operating system.
To solve it, follow these steps
1 - Open the command prompt with administrator privileges:

2 - Type the following command and press Enter afterwards:

If the OMDLG32.OCX file is present in the SysWOW64 folder and the operating system is 64-bit, go to this folder via the prompt: type ‘cd..’ press ENTER and then ‘cd SysWOW64’ and press ENTER

Enter the commands from point 2
3 - The message will appear

I get strange values for the safety factor, what could be the problem?¶
Check that the ‘Anisotropy’ command has not been selected in Stratigraphy, check that the slope has been defined as per convention: from left to right with increasing ordinates.
I cannot open files with the extension *.sta, from the previous version of Slope
I cannot open files with the extension *.sta, from the previous version of Slope¶
Within Slope 2022 there is a converter for files with the *.sta extension from previous versions. Simply click on the menu icon in the top right-hand corner and then on ‘Convert Files’.

The conversion tool will open:

I cannot understand how to define gabions in Slope.¶
Two approaches can be used to define slope gabions, the first is to define them as deformable walls and assign an average shear strength in terms of tension.
The other is to use the polygon tool and then treat the polygon as a material, in which case it is suggested to use apparent geotechnical parameters:
Apparent cohesion=(0.03M(gab)-0.05)98.1 [kPa].
Apparent shear strength angle= 25*ro(gab)-10 [°].
where:
M(gab) unit mass of wire mesh (kg/m^3)
ro(gab) overall density of the gabion mesh (Mg/m^3)
The programme does not take into account the presence of the water table, yet it has been included¶
Check that the layers, from ‘Stratigraphy’, have been defined as ‘Permeable’.
The programme does not perform the calculation.¶
Check that the section has been defined on the first quadrant of the co-ordinates (avoid negative co-ordinates) or that it does not have a large number of co-ordinate digits, if this is not the case translate the section.
I have defined intervention works, but I do not get an increase in the safety factor between the pre- and post-work situation. How come?¶
Check that the calculation method chosen is not Fellenius, it is the only one that does not take into account the intervention works.
What is the difference between the reinforcement element and the MRE module in Slope?¶
The reinforcing element, usually a geotextile, is inserted into the soil to provide increased resistance to sliding along a probable failure surface. It is used to model slopes or reinforced embankments. In Slope, the reinforcement element can be inserted punctually on the geotechnical section thanks to the specific command on the command bar (from Tests-loads-works >> Reinforcement element). The programme performs the stability check and provides a factor of safety considering the contribution of the reinforcement element.
MRE, on the other hand, is a module implemented in Slope and allows a reinforced ‘wall’ to be modelled and verified. The verifications that the programme provides are tilting, creep, limit load, buckling and failure of the reinforcement. In addition, the model created in MRE can be exported to Slope, inserted on the slope at the point where the intervention is planned and then the stability verification performed with the presence of the work.
Didn't find the answer? If your program has an active update plan, open a request on support.geostru.eu.